In our city, the Internet provider Beeline began to connect subscribers via the so-called "optics to the house" - FTTB - in parallel with Rostelecom. Dom.ru didn't even exist then. At first, various models of WiFi routers were offered, flashed with proprietary firmware - D-Link DIR-300, TrendNet, NetGear, etc. Then a new model appeared, which gradually replaced the rest - this is the Smart Box router. As it turned out later, this is actually the only good branded router not only for Beeline, but also among competing providers.
Setting up Smart Box yourself is very simple and there is no need to call a specialist. Now I will tell you how to do it.

Entering the configurator interface:

The IP address of the device in the local network (), as well as the login and password for entering the configurator ( admin / admin) can be found on the sticker located on the bottom of the case:

After that, open a web browser and enter the address - http://192.168.1.1. Press the Enter key and see this greeting.

Click on the "Continue" button and see the following authorization form:

We enter the login admin, the password admin and we get to the start menu of the Smart Box settings from Beeline.

Basic Smart Box setup

In the start menu, we need to call the configuration wizard, for which we click on the "Quick setup" button:

This will take you to the page where all the necessary parameters are collected. Honestly, as far as I remember, this was done by Dom.ru. On devices from Rostelecom and TTK, everything is much more complicated and confusing for an unprepared user.

In the field "Login" and "Password" you must enter the data for authorization in the billing Beeline. The account number is used as a login in our area. I think that it is organized this way in other areas as well.
In the "Network name" field, you need to come up with and enter the name of your home Wi-Fi network on the Smart Box. In the "Password" field, you also need to register a key phrase that the router will ask for when connecting to its Wi-Fi.
If you also connected the Beeline television, then in the very bottom section of the menu called "Beeline TV" you should mark the LAN port into which the set-top box will be connected. Click on the "Save" button.
That's all. You can check the operation of the device!

Something is not clear - watch the video instruction.

Smart Box firmware

As with any other router, you need to periodically update the firmware for Smart Box from Beeline to a more recent one. This measure is necessary, as the new firmware versions fix the problems that were in the previous ones. You can download the latest version on the official Beeline website - link.

In order to reflash the Smart Box router, you need to click on the "Advanced settings" button in the start menu:

In the window that appears, open the menu section Others >>> Software update:

Click on the "Select file" button, find and feed the firmware file to the Smartbox. Now you need to click the "Perform update" button. The following picture will appear:

After completing the process, the router will reboot itself. This usually does not reset the settings. But even if they are reset, do not be alarmed, according to the instructions above, you can set everything up yourself without any problems!

Working with other providers

Now the transition from one telecom operator to another is a quite common procedure. Everyone is looking for a cheaper tariff, faster speed, sweeter conditions. This is understandable and quite normal. The Smart Box router is locked on Beeline. But if you have a Superuser password, then you can configure it for other providers. And at the same time, everything is done on standard software and no alternative firmware is required. The elevated user login is SuperUser. Password for firmware up to version 2.0.24 inclusive - Beeline $ martB0x. After version 2.0.25, the superadmin password was changed. Now the serial number of the device of the form SF ********** is used in this capacity. You can see it on the sticker. For example, on my device it is SF13F4FF1F78.
Next, open Advanced Settings >> Others >> WAN... Smartbox works seamlessly with almost any other provider. Here is an example of setting it up for Rostelecom and Dom.ru:

The router supports virtual VLANs, which means that there will be no problems with interactive TV from Rostelecom, TTK, and Dom.ru!

Beeline firmware uploaded the current file. Beeline SB and SB O with firmware OW buy at. The cost of Beeline S B is 1800 rubles There are 3 web interfaces filled with beeline, rontel, and gpon. A LED, Beeline Router S B O has. Beeline alternative firmware added updated distribution. Video lesson demonstrating the control capabilities of the Beeline TV set-top box pause, rewind, record programs. Beeline S B unlock for all operators. Thank you said 205 times

Download the archive with the firmware files for B S B O and unpack it to a local drive, for example, in the folder F. Tag cloud Firmware tuner O 800, HUAWEI SAX MT882 how to flash and disconnect LINK at any, Beeline S B O, Alternative overview. Thank you said 618 times. Firmware router S B O dual-band WF router Beeline S B to B O. Software reinstallation is performed for the sole purpose of saving the router from the bugs of the previous firmware. You have become a subscriber of television and the Internet Beeline in Saratov, having connected under the action House of the 21st century and your apartment a day. Now, in the new My Beeline personal account, you can easily track your expenses, connect services. After flashing the Beeline router, it must be rebooted with a new firmware, after which S B

A more interesting option is to flash some popular alternative firmware on it, like or. B alternative firmware. Wait while the router is updating the firmware, this process takes approximately 5 minutes, after which the router. Thank you said 467 times. Router Beeline S B natural. Instructions for the router Beeline S B installation and configuration of equipment required for the current version of the firmware. B S B Alternative Firmware. Lying at home ownerless, scrapped immediately after connecting to Beeline L2TP, t

Thank you said 465 times. S firmware for other providers a fresh file has been uploaded. Download the latest firmware for B S B O and unpack. Firmware S S B O B S B brand. Router Beeline S B O. S alternative firmware download. Router Beeline S B O has four LAN outputs, provides. Router firmware added updated file

Carefully read the instructions for the B S BOX ONE and firmware. Alternative firmware of the router beeline uploaded the current distribution. Wait while the router is updating the firmware, this process takes approximately 5 minutes, after which the router is needed. Routers Beeline S B O. Starting with the firmware version, the superuser password has been changed to the serial number of the device SFXXXXXXXXXX. In our city, the Internet provider Beeline began to connect subscribers via the so-called optics to the FTTB house in parallel with. Beeline router alternative firmware uploaded a new archive. Beeline router firmware alternative firmware updated file uploaded

There is nothing secret when flashing the BS BOX ONE, so even an inexperienced user can perform this procedure. Now I took theirs S B, then SB O from. Beeline SB and SB O with firmware OW announcement for sale in Krasnodar. That is why I started looking for alternative firmware for a smart box and soon realized that they were not there and not in the near future. Internet router settings S B Firmware update. WF Beeline S B, or. S alternative firmware from the Beeline Forum. Hello everyone, so there is an S B O read as if it is identical to the usual S B! Other with tags, Beeline, Beeline, firmware

S B B N300 firmware [. You can download the current version of the firmware from the official Beeline website or from here.

Provider "Beeline", in order to keep up with others, decided to release its own router, the connection in which to the networks of this operator is configured with a couple of clicks. The router offered under the name Smart Box is built on the basis of the unified Realtek 8197D processor and is equipped with 64 MB of memory.

In fact, all claims that may be about the operation of this device relate more to the firmware. We hope it will be fixed soon. Let's consider how the proprietary Beeline router needs to be configured, and also how to update the firmware in it.

Router "Beeline Smart Box"

On the rear panel, in addition to the standard set of ports and the power button, you can see the mode switch. Router mode is activated when the toggle switch is in the up position. The second mode is "switch".

We will look at how to set up a connection with a Beeline provider. To do this, you can connect a computer to the router via a patch cord or wirelessly (which operates in mixed mode b / g / n, it is named “Smart_box-…”). Finally, we will discuss how to update the firmware. The firmware version current at the time of the review is 2.0.19.

Connection setup

To the WAN port, as you can easily understand, you need to connect the "Beeline" cord connector. You can access the router's web interface from a wired or Wi-Fi network (the latter works without a password).

The actions should be as follows: after connecting all the cables, supply power to the router, wait 1 minute, open the web interface. The requirement for configuring the network card is to set the "automatic" mode:

Setting up a wired connection on your computer

On wireless cards, they also include a similar mode ("auto" DNS and IP). The values ​​of the parameters that are needed to open the web interface are given below.

How do I open the GUI?

If a wired network is used to configure the router, the patch cord is connected to one of the LAN ports. In order for the network card to receive IP and DNS from the router, you need to right-click on the connection icon and click "Fix". You can connect to the wireless network without a password, its name looks like "Smart_box-XXXXXX".

Recall that the router is loaded for at least a minute. The address of the graphical interface for Smart Box is standard and equals 192.168.1.1. The default password is the same as the login, this is the word admin:

Logging into the graphical interface

Setting up a connection with "Beeline"

While on the start tab of the interface, click the "Quick setup" button. The following page will open:

Connection setup

Here you need to set the parameters:

1. Subscriber login of the form "089XXXXXX" (study the agreement)
2. Subscriber password - what is specified in the contract
3. "Network name" - can be left as it is
4. "Password" - the value of the Wi-Fi password (you may not use it at first)
5. We will not turn on the guest Wi-Fi network
6. We select one LAN port for the set-top box, if required (just not the one that is used now)
7. Click "Save"

Firmware upgrade

The built-in program for the router, that is, the firmware, can be downloaded from the official website of "Beeline". The firmware file occupies 16 or 17 megabytes. Save it to your "desktop". Next, we will look at how to reinstall the firmware in the Smart Box router, and most importantly, how not to make it worse.

Preliminary actions

It is best to do a factory reset before updating the firmware. We turn on the router, wait 2 minutes, press the reset button with a paper clip (the button must be held for 10-15 seconds). The LEDs should blink, then the router will boot up again (but with the default settings).

We will install the firmware by connecting the router to a PC via a wired network. It is necessary. Software reinstallation is performed for the sole purpose: to rid the router of the "bugs" of the previous firmware. If everything works well, nothing needs to be reinstalled.

It is important to know that during the transfer of the firmware file, you cannot turn off the power or break the connection between the devices. After the installation is complete, it is better to wait another 5 minutes, and only then briefly press reset.

Updating the firmware via the web interface

Go to the configuration graphical interface as discussed above. On the start tab, click the "Advanced settings" button. Then, select the "Others" -> "Software Update" tab:

Reinstalling the firmware

Sequencing:

1. Click "Select file", find the file on the "desktop" and click "Open"
2. Check the reliability of the connection again, click "Update"
3. Wait for the reinstallation to complete
4. Wait 5-6 minutes
5. Briefly press the reset button on the router

Successful setup!

Hello friends.
Probably, there is no such person who would not have heard about the Beeline company and their Internet of the same name. Like any "serious" provider, they like to install branded routers in the Beeline.

The pros are obvious: ease of setup and operation, as well as user support - the pieces of hardware are the same and possible problems have been known for a long time. And castrated, sharpened for the majority, the settings do not allow the user's playful hands to break everything.
This article discusses one of the most popular, widespread and, in general, a good router Beeline SmartBox.
As it should be in such cases 🙂 is an OEM device. True, these are not typical repainted DLinks, but exotic from SERCOMM)

In fact, the router is a slightly modified reference Realtek_RTL8197D.
You can see more details about him or below
Brand name: Beeline SmartBox.
Chip: Realtek 8197D (600 MHz)
RAM: 64 MB
Wi-Fi: 802.11b / g / n 300Mbps, 2 internal antennas: 2 × 2 MIMO
Interfaces: 5 RJ-45 connectors with auto-sensing cable type, USB 2.0 port

From software features: DLNA, FTP-server, SAMBA-server (connecting usb devices as a network drive), which makes it an interesting option for creating a simple home media center.
In general, the device is not bad and worked stably for me, giving out the tariff maximum over Wi-Fi.

However, as an enthusiast, I lacked freedom, SSHa and the ability to dig deeper inside, as well as the ability to fine-tune. That is why I started looking for alternative firmwares for the "smart box" and soon realized that they did not exist and would not be available in the near future ...
Well, the situation is unpleasant, but not hopeless. 🙂
Since there are no alternatives, you need to squeeze the maximum out of the stock, if possible, get a normal console and raise the privileges to root. And for this you need to merge and unpack the stock firmware.

Let's get started:

Attention... The following points are made from under a Linux system and I do not guarantee that you will be able to repeat all this under a Win-like OS.

When preparing, the following were used: Debian Lenny, binwalk, squashfs-tools, a little savvy and red-eyed.

1) I merge the latest firmware from here
wget http://static.beeline.ru/upload/images/help/devices/routers/SmartBox/SmartBox2019.zip
2) Unpacking 7zip, I find img file of incomprehensible, at first glance, content.
7z x SmartBox2019.zip
3) Run by passing as an argument img Schnick, to which he cheerfully reports about Secomm signatures and even tells us hardware id, but this is not the main point. Inside we find a pinched binar ( bin-file), unpack the archive and get

Binwalk output

S1000_Smart_box_SERCOMM_BEELINE_2019.bin which once again emphasizes the SERCOMM origin of the device 🙂

4) Here he is a binar, it would seem, happiness is near. But it was not there.
By itself, a binary file does not provide any human-readable information ( binary, cap).

And here the very anal carnival begins:
We set it again on it and among the signatures, bootloader and garbage we find squashfs ‘ Ofsky image (Briefly: Read-only file system, widely used when compressing * nix boot images).

Happiness is near, I thought. It remains only to unpack ...

Merging from the repository squashfs-tools containing everything you need to unpack and anticipating ... unsquashfs is talking

Filesystem uses lzma compression, this is unsupported by this version

Which means the file is craftily reaped lzma and he cannot unpack it.
Hmm, I climb on Github for the latest version squashfs-tools, collect from source and ... Again I break off.
After scratching the turnips and combing makefile I notice that support lzma disabled by default. I change the parameter and ... pay attention to the comment, which for LZMA required LZMA SDK.

Many customers of the Beeline company know about the release of the Smart Box Wi-Fi router and have purchased it for using the Internet and interactive television. This device is positioned as a modem for fast wireless Internet and meets all current standards to ensure high connection speeds.

The Beeline company issues devices for its customers

What is so special about Smart Box from Beeline? It is worth saying that the router is really good in terms of internal filling - it supports speeds up to 300 Mbit / s, has a sufficiently capacious RAM and outperforms other models in performance. The router has an additional USB port, and the built-in antennas are considered the only relative flaw in its design, which, however, provide a large signal coverage area.

To set the parameters of the router for the first time, do the following:

• Open the Smart Box menu - enter the IP-address of the device (192.168.1.1.) In the address bar of the browser, after the welcome message click “Continue”.
• In the authorization window, enter the value Admin on both lines. These data are standard, during subsequent configuration you can change them in order to secure the parameters of the equipment from unauthorized interference.
• Select the "Quick Setup" menu.
• In the window that appears, in the "Home Internet" fields, enter the login and the key given to you by the provider (you will find this information in the agreement).
• In the menu lines "Wi-Fi Router Network", come up with a name for your home network and set an Internet access password so that the connection is unavailable for.
• You can activate the "Guest network" section as you wish. If you want to create a separate network based on the router for your friends and acquaintances, come up with a name and an access key for it.
• Since the router has 4 LAN connectors, select the one on the bottom line to which you will connect the IPTV interactive television set-top box.

After entering all the necessary data, restart the equipment from Beeline - the corresponding command will appear when you save the changes.

Configuring Wi-Fi Settings

If you want to change the parameters of the Internet from Beeline, go to the router menu and follow these steps:

• Select "Advanced settings" and open the Wi-Fi section, on the left, select the main settings tab.
• The network SSID string is the name of the connection itself, which you change at your discretion.
• You can change the operating mode and channel. It is worth setting an automatic detection for the second function, then the router will be able to determine itself which channel to connect to. What is it for? If your neighbors also have a router and your device is on the same channel, the connection may not be effective enough. If you select the automatic mode, the router will switch itself to the less loaded channel.
• In the same smart box menu, you can disable the guest network by checking the box next to the corresponding line (do not forget to save the changes).

Internet connection security

To protect your connection from unauthorized access, just a good password is not enough - you should choose a reliable type of encryption for Smart Box. This is done like this:

• In the advanced settings, the Wi-Fi section, select the "Security" tab in the left menu.
• In the "Authentication" line, select the WPA2-PSK encryption type.
• In the same window below, you can change the access key for connecting to the network.

Updating the software

Each router has a separate firmware, which is constantly being refined and improved to make the device even more efficient, faster and more trouble-free. Therefore, you should update the firmware of your Wi-Fi equipment from time to time, which you can do as follows:

• Download the new firmware on the official website of the Beeline provider.
• We go to the initial menu of the router and select "Advanced settings".
• Open the "Others" section and click on the line for updating the software (software).
• Select "Select file" and specify the path to the downloaded firmware.
• The router will independently update the software, after which you need to restart it - disconnect and reconnect it to the power supply.

Port forwarding

Often, if you want to use a torrent client to download files or play online applications using Smart Box, you need to forward the port, that is, open it for the above purposes. How to do it?

All this is quite simple and will take a little time, just follow these directions:

• Select "Advanced Settings" again in the Wi-Fi router menu, the "Other" section.
• From the left menu select the NAT tab, Application Support.
• In the window that appears, you can select an application from the list or set your own value, for which you need to click on the "Set user service" button.
• If you are defining your service, enter the application name, select the protocol type and the desired port range in the next two lines.

Remember to save all changes! If, after the performed actions, torrenting or games are still unavailable, try selecting the DMZ Host line in the NAT tab - enter the IP address of your computer from which you open the port. Did not help? In this case, the problem lies not with the router, but with the security settings of the PC.

As you can see, setting up Smart Box from Beeline is quite simple and will make it easy and quick to start using the device for any user. Thanks to the provider's services and a powerful router, you can enjoy wireless Internet access with high speed, stable performance and a strong signal.