Question: How to set up the Internet on smartphones (phones) and tablets ZTE?

Answer: Internet setup on ZTE devices is performed in the following order.

1. We connect the service with the operator. This can usually be done via a USSD request.

To connect to the Internet from Megafon, we recommend that you follow the link - http://www.megafon.ru/internet/, select the type of device to connect, for example - "For a smartphone", select your region, then select a tariff, click "Buy", after what information will appear, what code you need to dial to connect the service, for example - *236*0#. We dial this code like a regular phone number.

To connect the Internet from MTS, we recommend that you follow the link - http://www.mts.ru/mobil_inet_and_tv/, select the type of device to connect, for example - "Internet from phone", after which a page will open with a code that you need to dial to connect services, for example - *252#.

To connect to the Internet from Beeline, we recommend that you follow the link - http://beeline.ru/customers/products/mobile/, select the type of device to connect, for example - "On the phone", then select tariff plan, then click on "To connect" -> "Connection and service management" after which you can see information on how to connect the service, for example, by dialing the code - *115*04# or by calling the number.

Attention! Page addresses and USSD request codes are for example only and may change over time! To connect, go to the main page of your website mobile operator and already since home page go to the pages with information about connecting to the Internet. For other operators, the setting will be approximately the same. You can also call your mobile operator at hotline and activate the service verbally. Another option is to come to any operator’s sales office in your city, where sellers must activate the service.

2. To turn on the Internet, you need to go to "Settings" -> "Data transfer" and opposite the item "Mob. traffic" or check the enable checkbox, or move the switch to the right to "On". For most ZTE smartphones, this is enough to automatic start mobile internet. After the connection is established, depending on the type of connection, in the notification panel, next to the network signal strength icon, the symbol H (HSDPA), G (GPRS), E (Edge), R (Roaming) or 3G will appear. Also, to check the Internet connection, open the browser and wait for any web page to load, for example, by typing “ya.ru” (light version of Yandex) in the address bar.

Attention! If a smartphone 2-SIM, then the SIM card that will be used to access the Internet must be inserted into the WCDMA / GSM connector, and in the settings "Settings" -> "More" -> " Mobile network» -> « Network settings SIM1″ (or 2 depending on the model, see the slot number under the cover) -> "Network mode" -> "Preferred network mode" -> "GSM / WCDMA" or only "WCDMA".

3. If the Internet does not appear on your ZTE device after following the previous recommendations, then you must either receive the Internet settings from your mobile operator in automatic mode, or enter the settings manually.

Automatic setting

If the operator is Megafon, then go to the site - megafon.ru, click on the link "Support" -> "Settings", select "ZTE" there, and then your smartphone model, for example - "V880E" and enter your phone number. After that, the settings should come to your device.

If the operator is MTS, then go to the site mts.ru, then " Mobile Internet and TV" -> "Help and Service" -> "Settings" -> "Phone settings". There we enter the number and wait for the settings to be received.

If Beeline operator, then auto tuning mobile Internet is ordered by a free call to 0880. (The password for saving settings is 1234.)

Manual setting

If the operator is Megafon, then go to http://labs.megafon.ru/dev/, there we select "Other manufacturers" -> "ZTE", we are looking for our device, for example "ZTE Nubia Z5", well, we are trying to set it up like this, as it is written there.

If the operator is Beeline, then go to the site beeline.ru, there click on the link "Help and support" -> "Internet settings" in the search field, enter the model of your device, for example - ZTE V790 and then click "Find instructions" and read the information on at the construction site. You can also send instructions directly to your phone by selecting the link "Send SMS with instructions for ZTE V790".

If the operator is MTS, then go to the site mts.ru, then "Mobile Internet and TV" -> "Help and Service" -> "Settings" -> "Phone Settings" -> "Internet" -> "Android", read the instructions .

General rules for manual configuration

Go to "Settings" -> "More" -> "Mobile network". If 2 Sim-cards are used, then select the settings of the Sim-card for which the Internet is activated. Next, click on the item "APN access points" -\u003e " New point access "and enter the settings that are indicated on the website of your mobile operator. After entering the settings, save the access point, reboot the device and rejoice.

In most cases, the following settings will suffice.

ZTE ZXA10 F660 is a home gateway module for GPON optical network. In other words, this is equipment that is installed directly at the client. In appearance, the ZTE 660 resembles a regular WI FI router. However, this impression is deceptive, since a lot of functions are combined in a small device.

The first difference from other client terminals is the use of modern xPON optical communication technologies. The second and no less important difference is versatility. Now, in addition to connecting four desktop computers or internal networks via Ethernet ports (RJ 45) and several clients via WI-FI, the ability to support flash drives is implemented USB standard 2.0 and IPTV support. There are also two POTS ports (RJ 11) that allow you to connect telephones and use IP-telephony in parallel with other functions without loss of communication quality. The terminal also boasts many other positive qualities, including environmental friendliness, constant software updates and full support manufacturer's representatives in many countries of the world.

Specifications and functions of ZTE 660

Terminal specifications:

User interfaces:

• RJ-11 (POTS) - 2 (designed to connect telephone sets and their further operation using IP telephony).
• RJ-45 (Ethernet) - 4 (3x1 Gbps for connecting desktop computers + 1 IPTV for TVs).

SC/UPC (Optical interface) - 1:

• Fiber type - single-mode;
• Interface standard - ITU-T 984.x;
• The speed of receiving / transmitting information - 2.488 Gb / s / 1.244 Gb / s;
• Optical signal output power - from 0.5 dBm to 5 dBm;

The length of the fiber optic channel is up to 20 km.

USB - 1 (standard 2.0 is supported).

• frequency - 2.4 MHz;
• standards - IEEE802.11b and IEEE802.11g;
• manual and automatic selection channels;
• signal strength change function;
• support for 4 SSID networks simultaneously (128 clients per network);
• WEP, WMM, WPS, WPA/WPA2PSK, WPA2PSK and WPA PSK encryption.

• Virtual local table computer network - 4000;
• MAC address table - 4000;
• Multicast table - 1000.

System startup time - 50 s.

Consumed voltage and power - 12V/11W.

Overall dimensions (width/height/depth) - 199mm/35mm/150mm.

Weight - 0.7 kg.

Equipment delivery set:

• terminal - 1;
• power adapter 12V - 1;
• patch cord - 1;
• instruction ZTE 660 - 1;

Terminal functions:

• GPON - Bandwidth allocation, GEM adaptation, T-CONT, Measurement of parameters and diagnostics of optical channels;
• WIFI;
• VoIP - technology for making telephone calls via the Internet;
• ETH Functions - ETH OAM, MAC Address Handling, VLAN Handling;
• Multicast data transmission;
• Data forwarding and routing at layer 3;
• IPv6 support - new protocol using 128 bit address length;
• Control functions;
• Security mechanisms - Data protection on the GPON interface, Traffic suppression;
• Energy saving in GPON system;
• Alarm;
• Maintain performance statistics for Ethernet ports.

Configuring ZTE 660

After installing the equipment in its place, it is necessary to carry out the procedure for setting it up. To do this, you will need to perform the following steps:

• Connect one end of the connecting cable (patch cord) to one of the four Ethernet ports, and the other to a computer or laptop;
• Open any browser (for example, Opera);
• In the address bar, enter the following inscription 192.168.1.1;
• In the window that opens, a sign should appear prompting you to enter a login and password to access the hardware settings. Enter “admin” in the “admin” fields and click on the “Login” button.

After checking the entered information, the browser will open a new window in which the equipment model will be indicated, serial number, chip and firmware version, ZTE 660 password.

To enable the hardware WI FI function, you must:

• Go to the "Network" tab located at the top of the open page;
• In the “Basic” window that opens, change the value in the “Wireless RF Mode” column to “Enabled”;

After completing this action, you must confirm it by clicking on the "Submit" button.

WI-FI network settings on the ZTE ZXA10 F660 router:

• Go to the "Network" tab located at the top of the open page;
• Next, in the side of the page, you need to click on the link "WLAN";
• Now you need to go to the "Multi-SSID" item.

Here you can change:

• Network ID name "SSID Name";
• Enable or disable the "Enable SSID" changeable network function and select it "Choose SSID";
• Hide its visibility "Hide SSID";
• Define the number of simultaneously connected GEM "Maximum Clients" ports (default is 32).

After making all the changes, confirm them by clicking on the "Submit" button.

To configure WI FI security in ZTE 660, you must:

• Go to the "Network" tab, which is located at the top of the open page.
• On the side of the page, click on the "WLAN" link.
• Next, go to the "Security" tab on the left side of the screen.
• In the "Choose SSID" field, select the network ID you need to change the settings.
• In the "Authentication Type" field, select how you want to access your network: " open system» - open system; Shared key - public key;
  "WPA-PSK", "WPA2-PSK", and "WPA-WPA2" are private key authentication types.
• In the "WPA Passphrase" field, enter your personal network access code.

Important! Here it is immediately worth saying that in order to protect against unauthorized entry, a reliable key should be created. To do this, it must simultaneously contain numbers and alphabetic characters of both upper and lower case (uppercase and lowercase), and the length of the code itself must be at least 10 characters.

In the "WPA Encryption Algorithm" field, select an algorithm for encrypting data on the network.

After making all the changes, confirm them and click on the "Submit" button.

If you don't see your router's IP address in the list above. There are two additional ways determining the IP address of your router:

1. You can also follow the How to Find Your Router Address guide.
2. Or you can use our free software, called the router's IP address.

Now that you have internal IP address your router, we are ready to enter it.

Login to the ZTE router, through the web interface in a web browser

ZTE has a web interface for configuration. You can use any web browser you need to log in to ZTE. In this example, we will use Internet Explorer.

Enter ZTE internal IP address

Put your ZTE's internal IP address in address bar your web browser. It looks like this:

Then press the Enter key on your keyboard. A dialog box will appear asking for your ZTE username and password.

ZTE router password and default username

You need to know the username and password to login to ZTE. All default usernames and passwords for ZTE are listed below.

Enter your username and ZTE password in the dialog box that appears.

Steps to Change WiFi Password for SLT ADSL - ZTE

1. Open a browser and type 192.168.1.1 and press Enter.

2. Then a pop-up window will open and ask you to enter your credentials. Enter the username as admin and password as admin and click the login button. (This is the default username and password for the SLT router configuration page, you can change it at any time after logging into the router configuration page)

3. The router configuration page will open and click menu INTERFACE SETUP, and then select Wireless(see image below).

4. Now go to the bottom of the page to the section wifi password and change the WiFi password.
Changing the Pre-Shared key will change the password of the WiFi router.

5. After entering your password, scroll down to the bottom of the page and click the Save button.

6. That's all. You have successfully changed your ZTE password.

Forgot ZTE router password? Need to reset the ZTE router

Have you changed the username and/or password of your ZTE router and forgot what you changed it to?
Do not worry: All ZTE routers come with a factory default password that you can reset to by following the instructions below.

Resetting your router to factory defaults is a serious step. However, sometimes when you have no other way to access your router, this step is necessary. In particular, if you can't log into your router normally (perhaps because you've forgotten your password), this may be your only resource. Before resetting the router to factory settings, make sure that the passwords do not work, including the default passwords.

Reset ZTE router to default, this will reset ZTE password to default

If you decide to return your ZTE router to factory default settings, you must perform a 30-30-30 reset as follows:

1. When your ZTE router is turned on, press and hold the reset button for 30 seconds.

2. While holding down the reset button, power off the router and hold the reset button for another 30 seconds.

3. While holding the reset button, power on the device again and hold for another 30 seconds.

Your ZTE router should now be reset to its new factory settings. Check the table to see what it is (Most likely No/No).
Important: don't forget to change the default username and password to increase the security of your router after a factory reset, since the default passwords are available all over the internet (for example, here).

I still can't access my ZTE with the default password

Make sure you follow the reset instructions correctly, as the router should always return to factory default settings (ZTE password and login) upon reset. Otherwise, there is always a risk of damage to your router and it may need to be repaired or replaced.

How to change the wireless channel on my wifi

Example. On performance wireless router may be affected by interference from other nearby routers. You can change the wireless channel to one with less interference.

Step 1. Open an internet browser (such as Internet Explorer) and enter http://dlinkrouter.local or http://192.168.0.1 into the address bar. Press Enter.

Step 2 Enter password for account administrator in the field. If you have not changed this default password, leave the field blank. Click Login.

Step 3: Move your cursor to the "Settings" tab and then click " Wireless connection» in the drop-down menu.

Step 4: Click " Additional settings» for the band for which you want to change the wireless channel. Select a channel from the drop-down menu " WiFi Channel». The mode selection process is the same for the 2.4GHz and 5GHz bands, but the options available for each band are different.

Band 2.4 GHz:

5 GHz band:

Note. In most cases, you only need to change the channel on your router. Majority wireless adapters automatically detect the channel used by your wireless network.

Change LAN IP address on ZTE

If you followed our navigation guide above, you should see this screen.

We start this guide on home page ZTE router. Want to change your IP address? You have come to the right place. We'll show you how.