We carry out a full range of repair work on iPhones flooded with water and liquids. We carry out complex repairs including replacing chips, discrete elements, power circuits, and restoring conductive paths.

The procedure for performing repair work on an iPhone filled with liquid:

• We diagnose a flooded iPhone. Diagnostics are carried out within 24 hours. Such a long period is due to the identification of all faulty components, as well as an assessment of the nature of the damage.
• We contact the client and fully describe the necessary repair work. After diagnostics, managers contact the client in a way convenient for the client: telephone, e-mail, provide the entire fault map, and also name the exact amount of repairs.
• Repairing a flooded iPhone. Repair work on iPhones filled with liquid is usually carried out within 1 to 4 working days. After the repair, the iPhone is tested for 12 hours; if the testing does not reveal any faults, the iPhone is sent back for delivery.
• Payment for repair work. Payment is due after iPhone checks client. You can pay as follows: by bank card, in cash and by bank transfer.

The most common types of damage to flooded iPhones

• Filled iPhone by water. Most common when using iPhone in the rain or in countries with a humid climate. Moisture gets inside the device, which leads to a short circuit; as a result of a short circuit, discrete elements, controllers, and power circuits on the motherboard fail.
• I filled the iPhone with liquid (alcoholic drinks). The malfunctions in this case are the same as in the case of flooding with water.
• iPhone is filled with viscous liquid. It is less common, viscous liquids are usually very difficult to clean, contact with the microphone, ear speakers, polyphonic speakers viscous liquid leads to failure of these components. In case of contact with viscous liquid, failure motherboard iPhones are seen less frequently.

A little about how we repair a flooded iPhone

After the iPhone is received by a specialist in the technical department, the specialist completely cleans the iPhone from liquids and moisture in an ultrasonic chamber. After the ultrasonic chamber, all components of the iPhone are completely dried. After the iPhone has dried, motherboard faults are identified on a hardware bench. After identifying a fault, the specialist makes a complete fault map and transmits the information to managers. After confirming the customer's repair, the specialist begins repair work. Repairs are carried out at a highly qualified level using original components, as well as professional equipment with factory soldering quality. After the repair of the iPhone motherboard is completed, a full test is carried out; if malfunctions are identified during the testing process, the specialist eliminates them. After passing the quality control department, the specialist places the iPhone for delivery.

Alexander

20.12.2016, 23:26

Answer: Good morning, Alexander. After liquid gets into the iPhone, the first thing you need to do is turn off the power to the device and remove any remaining liquid to avoid the formation of oxides on the system board and connectors. For visible work, it is necessary to diagnose the device, since the range of problems is quite wide, such as an error in the operation of the controllers, a short circuit, damage to discrete elements, and a malfunction in the iPhone power supply circuit is also possible. Diagnostics are carried out free of charge, it will show whether intervention in the device is required or not, but in any case, no repair work is carried out without approval and agreement with you. According to experience, the cost of repairs is from 1000 rubles. Thank you for your request.

18.12.2016, 10:22

Answer: Good day, Elena. After moisture gets on the device, you first need to turn off the power to the device and remove any remaining liquid to avoid the formation of oxides on the system board and connectors. For visible work, diagnostics of the device is necessary, since the range of the problem is quite wide: it can be either a short circuit or one of the controllers can be flooded, since the semiconductor elements that make up the iPhone 6s Plus are quite sensitive to moisture. Based on experience, chemical cleaning of the device will be required, in most cases it is sufficient. Cost 1800. Thank you for contacting.

Answer: Good morning, Dmitriy. After moisture has penetrated, you should first turn off the power to the device and remove the moisture before oxides form on the system board and connectors. The device is heating up due to incorrect current distribution in the iPhone system; in technical language, a short circuit. The system overheats and the device shuts down urgently. This threatens the loss of working capacity as a whole. In this case, chemical cleaning of the device is required, which is performed on specialized equipment, namely in an ultrasonic bath; in most cases it is sufficient. For visible work, it is necessary to diagnose the device, since it is important to determine in which component of the phone the problem occurs. this error. Diagnostics are performed free of charge. It will show whether intervention in the device is required or not. But in any case, no repair work is carried out without approval and agreement with you. Thank you for your request.

Answer: Good afternoon, Vadim. In this case, you should first of all turn off the device and disconnect the power until the liquid is eliminated, in order to avoid the formation of oxides on the system board and connectors. The device contains several speakers, these are polyphonic and voice, an error in this case is possible specifically in polyphonic, and errors can also be associated with problems in the audio codec chip. Visible work requires diagnostics of the device. Diagnostics are free, please contact us.

Answer: Good afternoon, Denis. The problem is in the modem node. If the modem chip itself fails, the device cannot be repaired; there are a lot of elements responsible for the operation of the modem: the modem power controller, discrete elements, conductive paths, accompanying microcircuits, or if the modem chip has physically moved away from the base of the board. In these cases, repairs can be made. In 98% of cases, our specialists can fix any problem. Come for a free hardware diagnostic, after which we will be able to clearly determine the reason for this behavior of your device and guide you possible options its restoration.

Answer: Hello. Approximately, the liquid could penetrate into the PCB layers of your device. It is necessary to diagnose your device as the range of variations of the problem may vary. Our service center has specialized hardware stands to solve this problem, please contact us, we will be happy to help you.

Answer: Good afternoon, Vladimir. In case of moisture penetration, comprehensive chemical cleaning of the device is necessary, since corrosion spreads extremely quickly. As a rule, cleaning helps eliminate the problem. In such cases, you must turn off your device to avoid a short circuit. Bring your device to our service center for cleaning.

Answer: Good afternoon Olesya. Remotely, it is difficult to understand exactly what the problem is. Come to our service center at free diagnostics, let's see what's wrong with your device.

27.03.2016, 21:43

Answer: Good afternoon Maria. If it gets into the device, the board begins to oxidize; in your case, the touchscreen controllers or the display itself were most likely damaged. Come to our service center, we’ll conduct a free diagnosis and see what your problem is.

19.02.2016, 23:09

Answer: Good afternoon Irina. Replacing the motherboard is not practical; the cost is 70% of the device. In most cases, the board can be repaired, come for diagnostics and we’ll see what can be done. We will be happy to help you.

11.02.2016, 06:32

Answer: Good morning. After pouring it is necessary to carry out dry cleaning. Bring it in for free diagnostics, we will remove your drive and give it to you. We also remind you that Mac OS has disk encryption, in which the data in any case will not be available when diagnosing and repairing your MacBook Air. We cannot let you into the technical department; the technical department contains quite expensive equipment, customer devices, and components. Only financially responsible employees are allowed into the technical department; therefore, specialists do not perform diagnostics in front of the client.

Answer: Good day, Sergey. When moisture gets into the device, the board begins to oxidize; it is necessary to do dry cleaning. Come to our center, we will conduct a free diagnosis, and see what can be done.

04.01.2016, 23:51

Answer: Hello, the speaker will need to be either replaced or cleaned. Chemical cleaning of the device itself, since if moisture gets in, it remains inside, which causes corrosion and possible rotting of the board in the future. Bring us for a free diagnosis, we can more accurately guide you on this problem.

Answer: Hello. Unfortunately, it is not possible to predict the further condition of the device after moisture has been introduced. We advise you to contact the service center. At a minimum, the device must be chemically cleaned to remove any remaining liquid to avoid a short circuit on the system board.

24.08.2015, 20:58

Answer: Hello. Most likely the problem is on the system board. Replacement motherboard only if the device is technically beyond repair. Bring your device and we will perform a free hardware diagnostic. We can tell you exactly what is faulty and determine the timing and cost of repairs. We carry out repairs of any complexity.

Answer: Hello, Anastasia! Fogged glass indicates residual liquid in the device, a burning chamber indicates a short circuit in the power circuits. In such situations, you should immediately turn off the device and disconnect the battery. Next, remove any remaining liquid and corrosion from the motherboard by dry cleaning. Afterwards it is possible to determine possible problems in the device itself. Come, it will be possible to do this as part of the diagnostics.

21.08.2015, 15:35

Answer: Good afternoon, Marina! In this case, you can come to our service center to conduct a free hardware diagnostic, after which we will tell you exactly whether there is moisture inside or not. Come, we will be glad to help you!

Anastasia

15.08.2015, 01:08

Answer: Hello. Unfortunately, it is difficult to determine the extent of damage remotely. It is necessary to perform hardware diagnostics. Bring the device to our service center, diagnostics are absolutely free, within a period of 2 hours to 24 hours. After diagnostics, it will be clear whether restoration of functionality is possible. We repair motherboards of any category.

14.08.2015, 09:18

Answer: Hello. We advise you to contact the service center for free hardware diagnostics. It is necessary to disconnect the battery as soon as possible to prevent further rotting of the system board and the spread of corrosion. At a minimum, dry cleaning is necessary to remove any remaining liquid and remove any oxide that has formed. The problem may be in the display module or on the system board.

Anastasia

18.07.2015, 22:50

Answer: Good afternoon Restoring functionality is possible, if possible, the device will work without any “glitches”; if repair is impossible, then replacing the board seems irrational due to the cost of repair work and components.

13.07.2015, 10:49

Answer: Good day, Andrey! After the iPhone is flooded with water and liquids, as a rule, the elements begin to oxidize, which leads to complete failure of the iPhone. In this case, we recommend preventive cleaning and diagnostics of the iPhone for faults.

06.07.2015, 10:36

Answer: Hello. This problem may be associated either with a malfunction of the display itself or with the failure of elements on the system board. Unfortunately, it is not possible to diagnose this malfunction remotely. We advise you to contact the service center for free hardware diagnostics.

Answer: Hello. The problem may be associated with a failure of the battery, a malfunction of the power controller, or discrete elements. Unfortunately, it is not possible to diagnose this malfunction remotely. After pouring, at a minimum, dry cleaning is necessary. We advise you to contact the service center for free hardware diagnostics.

Answer: Good afternoon, Yulia! Do not connect power and, if possible, do not turn it on. When you come to Moscow, hardware diagnostics are carried out free of charge.

Elizabeth

27.04.2015, 09:10

Answer: Good morning, Elizabeth. Unfortunately, your case is not under warranty and repairs will not be covered under warranty. In this case, I recommend carrying out free diagnostics and cleaning after flooding. Come and tell us what work is needed after free testing.

24.04.2015, 18:16

Answer: Hello! Most likely the problem is in the display module. However, if replacing the camera did not help and the device was flooded, then most likely there is a malfunction on the system board. We will be able to say more accurately after conducting free hardware diagnostics.

21.04.2015, 15:49

Answer: Good afternoon, Adam! In this case, it is necessary to carry out hardware diagnostics of the device. The problem in this case may be battery or power supply elements on the system board. Come and tell us exactly what happened after testing the device for free.

Answer: Good morning, Olga! The reason may be discrete elements or loops. We will definitely be able to answer your question after performing a free hardware diagnostic.

Answer: Hello! If moisture gets in, at a minimum, dry cleaning is necessary to prevent corrosion. The earpiece may also need to be replaced. Dry cleaning 1500 rubles. Bring your device, we will perform free hardware diagnostics, identify faults and how to eliminate them.

30.01.2015, 18:53

Answer: Most likely the display module is faulty. Unfortunately, we will not be able to determine the problem remotely. Bring your device and we will perform a free hardware diagnostic.

24.01.2015, 08:29

Answer: Hello! As a result of the flood, corrosion and rotting of the board could begin. Short circuits on the system board and in the power supply circuits are also possible. Unfortunately, it is not possible to diagnose this malfunction remotely. Bring your device and we will perform a free hardware diagnostic. We will accurately identify the fault and determine the time and cost of repairs. At a minimum, your device must be chemically cleaned to remove any remaining liquid. It is advisable not to turn on your device.

14.01.2015, 18:33

Answer: Most likely the problem is in the power circuits, the power controller (failure), discrete elements. The chance of recovery is 70%, taking into account that the device will arrive at the service center in the next 2 days, then oxidation begins. Naturally, if the iPhone motherboard cannot be repaired, you will have to replace it.

14.01.2015, 08:47

Answer: Yes, you can sync your iPhone by connecting it to iTunes in DFU mode. We can also offer you repairs for your iPhone, if it turns on, there is a high probability that the repair will be feasible.

Answer: The problem is a short circuit; after moisture enters, the power circuits and key components of the iPhone oxidize. If you do not clean it from moisture, the iPhone is more likely to fail.

Answer: Most likely the problem is in the power circuits, namely a short circuit. It is also possible that the power controller has failed. You can accurately identify the fault in our service center after conducting a free diagnosis of your iPhone.

Vladislav

21.12.2014, 17:46

Answer: Bring the device to our service center, we will carry out free diagnostics and identify the cause of the malfunction. After diagnostics, we will tell you exactly whether the device can be restored, and if so, the exact cost and time frame for repairs.

Answer: Most common problem after flooding the iPhone with liquid - oxidation of the conductive paths and elements of the iPhone. When oxidized, the device begins to quickly discharge, various components fail, resulting in complete failure of the motherboard and the impossibility of repair. It is not possible to say remotely what exactly went wrong in your case. Bring the device to the service center, we will carry out free hardware diagnostics and identify the fault.

14.12.2014, 14:01

Answer: The problem you described may be caused by the power controller, power circuits, or discrete elements. Unfortunately, it is not possible to determine the fault remotely. It is possible to accurately identify the cause of the malfunction in our service center after conducting a free diagnosis of your iPhone.

02.12.2014, 20:29

Answer: After salt water, without dry cleaning, all elements of the iPhone begin to rot. In your case the problem may be entirely different components motherboard. It is possible to accurately identify the fault in our service center after conducting a free diagnosis of your iPhone. After the diagnosis, you will know the exact cost and timing of repairs.

30.11.2014, 19:51

Answer: Most likely, after the iPhone was flooded, a short circuit occurred after the motherboard dried out. It is not possible to accurately identify the fault remotely. Bring the device to the service center, we will carry out free diagnostics, identify the fault and accurately estimate the cost of repair.

Answer: Most likely the problem is in the power circuits, or the touchscreen cable has come loose. You can accurately determine the cause of the malfunction in our service center after conducting a free diagnosis of your iPhone.

Answer: To estimate the cost of repairs, you need to bring your iPhone to a service center, we will carry out free diagnostics, identify faults and accurately tell you the time and cost of repairs.

09.10.2014, 18:00

Answer: Hello Olga. We restore flooded iPhones 80% of the time. Rice is an epic fail that is common on the Internet and does not provide any benefit for drying the iPhone. Bring your device to the service center, we will carry out dry cleaning, identify faults, if any, after carrying out free diagnostics and, if necessary, make repairs.

24.09.2014, 13:32

Answer: It is possible to assess the nature of the damage only in the service center after conducting a free hardware diagnostic of your iPhone. Chance of recovery is 40%. It is possible to tell the exact cost after we understand what is faulty.

Answer: Good afternoon, Christina! In this case, it is necessary to carry out dry cleaning, since oxidation occurs on the motherboard. Hardware diagnostics are carried out absolutely free, come!

26.08.2014, 09:23

Answer: Good afternoon, Azha! Most likely there is a problem with the touchscreen controller. Contact a specialized service center in your city to diagnose the device.

Answer: Hello. I think the problem is in the power circuits or controllers; it is not possible to remotely determine the cause of the malfunction. It is possible to say for sure after a free diagnosis at our service center.

03.08.2014, 18:15

Answer: Good afternoon, Ksenia! In this case, there may be a problem in the upper loop, as well as in chips, discrete elements, and power circuits. We will definitely be able to answer your question after conducting free hardware diagnostics at the service center.

Anatoly

27.07.2014, 02:03

Answer: Anatoly, hello! Micro cracks on the board occur from impacts; the problem may not immediately appear; it is enough to remove the board from the mounting unit on the case; a hidden defect may make itself felt. Micro cracks and damage to the processor cannot be cured. As a rule, in such situations, we recommend purchasing a new device.

Answer: There may be a problem with the power controller, battery, or power circuits. In this case, it is not possible to determine the fault remotely. If you want to find out the exact cause of the malfunction, you must submit your device for hardware diagnostics. Come - this procedure is free.

Answer: Anastasia, hello. Repair is possible, but it is necessary to determine the fault points. Come, after carrying out hardware diagnostics we will be able to advise you on the cost and timing of repair work

17.07.2014, 09:37

Answer: Good afternoon, Boris! In this case the error central processor or device flash memory. We will be able to tell you the possibility of restoration and the cost of repairs after a free diagnosis.

29.06.2014, 11:06

Answer: Stanislav, increased consumption can be calculated and eliminated, it is necessary to measure the power consumption of the main power controllers, and also test the power circuits, come, this procedure produced free of charge.

Answer: Good day, Sergey! The problem is most likely in the battery or power circuits. Come and let us tell you exactly what happened after a free diagnosis.

The motherboard on the iPhone is a complex system chip that contains soldered control electronic modules: processor (A6-A9), RAM (16 - 128 Gb), microcontrollers touch screen, USB, Wi-Fi, power supply, frequency duplexer filters, transceivers, power amplifiers and a number of switching device microcircuits.

The motherboard is the “heart” and “brain” of the mobile Apple phone. It is hidden under the display module and is well protected from the “rear” by aluminum back cover housings. However, if there are strong mechanical shocks or water gets inside the device, it can easily fail, which will require complex and expensive repairs.

When is it necessary to replace the motherboard on an iPhone?

Mechanical damage or water getting inside the device are the most common causes of motherboard failure on an iPhone. Individual soldered components can sometimes be repaired separately, but usually a complete replacement of the iPhone motherboard is required if:

• mechanical damage or cracks have appeared on the microcircuit itself;
• more than 50% of the microassembly components burned out due to contact oxidation or short circuit.

Apple device service specialists classify iPhone motherboard repair as the most complex type of restoration repair, and recommend contacting professional service centers in such situations.

iPhone motherboard repair

In case of minor damage to individual modules associated with motherboard, it is possible to restore them autonomously, but most often the system board completely fails and it is necessary to replace the entire iPhone board. This technology reduces the gadget recovery time to 30-40 minutes and eliminates accidental damage to cables and still serviceable components.

However, you most likely will not be able to repair the iPhone board yourself, because:

• To determine the real causes of the breakdown, phone diagnostics is necessary;
• It is impossible to disassemble a smartphone without a special tool and practical experience;
• For replacement, only original components are required.

If replacing the motherboard on your iPhone is inevitable, contact a specialist with this problem. service center“Honest Service”, which provides professional and inexpensive restoration of Apple mobile devices in Moscow and St. Petersburg.

Procedure for replacing the motherboard in an iPhone

To repair the iPhone board, certified engineers of the Honest Service service center perform a complex cycle of work, which includes:

• mandatory preliminary diagnosis of telephone malfunctions;
• complete disassembly of the device (removing the display module, disconnecting the screen, camera, touchscreen and connectors cables, battery, antenna cable, top cable, Power button cable);
• dismantling the motherboard and replacing it with a new original spare part;
• assembly and testing mobile device;
• issuing a guarantee for repairs.

Why “Honest Service”

If you do not want to complicate the repair of the system board and pay a high cost for it, contact the certified engineers of the Honest Service center - rational decision, as you will be offered:

• mandatory free phone diagnostics;
• modern mobile device repair technologies and special tools;
• wide selection of original components;
• the ability to replace the system board at home in your presence;
• optimal affordable prices and a one-year warranty on work performed.

our team

Ruslan Volontir

Field engineer

Sergey Fadeev

Master Receiver

Gennady Naumov

Andrey Popov

Dmitry Shcherbina

Supervisor

Cost of services:

Model	Price
iPhone 4	2490 ₽
iPhone 4s	2490 ₽
iPhone 5	2990 ₽
iPhone 5s	2990 ₽
iPhone 5c	2990 ₽
iPhone 6	3700 ₽
iPhone 6 Plus	4700 ₽
iPhone 6s	4700 ₽
iPhone 6s Plus	6490 ₽
iPhone SE	2990 ₽
iPhone 7	6490 ₽
iPhone 7 Plus	8490 ₽
iPhone X	21900 ₽
iPhone 8	9990 ₽
iPhone 8 Plus	11990 ₽
iPhone XR	22900 ₽
iPhone XS MAX	27990 ₽
iPhone XS	23990 ₽

Today, there are no particular difficulties with repairing Californian smartphones. Even in a small provincial town there is a workshop where you can repair the “hopeless bitten by fate.” However, the process iPhone recovery 5, the motherboard of which is considered “difficult to lift” will require considerable financial costs on the part of the owner. Why pay extra? To languish in anticipation? Strain your brain with doubts about: “How high quality will the installed part be?” Isn't it easier to get some recommendations and solve the problem yourself? Well, let's save money!

IPhone 5. Motherboard

The description of this part can be reduced to listing the main hardware components of the smartphone. It may be useful for some readers to know what exactly is under the shielding casings of the fifth model.

• The A6 processor is located above the SIM receiver.
• The accelerometer and two touchscreen controllers are located just above the CPU.
• The reverse side of the board (directly below the processor) is equipped with a flash memory chip, above which there are: auxiliary memory (LTE), a gyroscope and a Wi-Fi module.
• Two power controllers are located slightly below.

It is worth noting that the CPU is filled with a special substance - a compound, which significantly complicates the process of repairing it.

It works - don't touch it!

For the iPhone 5 to be a worthwhile process, you need to be sure that the part really needs to be replaced. Far-fetched reasons: “something is not working” or “the system board is probably damaged” is not yet a reason for a radical modification of your “humble electronic servant”. You must have good reasons for making this type of decision. After all, the motherboard of a smartphone is, in fact, the mobile phone itself. As you can imagine, a mistake can cost you dearly. Therefore, it is necessary to clearly understand what exactly is the reason iPhone breakdown 5.

The motherboard needs to be replaced if...

• The smartphone was subject to a short circuit.
• Some parts of the frame get very hot.
• The phone fell “hard”.
• Visually there are signs of deformation of the case: fractures, kinks and other types of “asymmetry”.

Any mechanical damage to a smartphone that causes partial or complete loss of functionality of the device, first of all, requires software diagnostics. However, when you are completely sure that the main board has failed, follow the instructions below.

Removing the main part of the smartphone

As mentioned earlier, repairing the iPhone 5 motherboard is, in principle, possible, but due to the complex arrangement of components and the use of some technological “chips” by the manufacturer during factory installation, this is an incredibly labor-intensive task, in general, doomed to failure (even in the hands of experienced craftsmen). As practice shows, it is much more advisable to purchase a new or working used board.

So, to directly install a working motherboard you will need:

• Apple screwdriver set.
• Tweezers.
• Plastic spatula (old credit card).
• Suction cup for removing the screen module of iPhone 5.

The motherboard can be easily removed. However, you simply cannot do without this tool. Believe me, using traditional screwdrivers will not lead to anything good - it has been proven!

Step one: remove the battery

• Unscrew the two end bolts on the front of the smartphone.
• Using a suction cup, carefully lift the bottom edge of the screen module.

Attention: in the upper right corner (underneath there are connecting cables that can be damaged if handled carelessly.

• Unscrew the protective cover of the connectors (very top, right) - three screws.
• Disconnect the touch and display cables.
• To the right of the battery (under the SIM receiver), unscrew two more protective elements.
• Disconnect the battery connector and remove the battery from the case.

Second action: disconnecting the piping loops

Once you have managed to remove the battery, turn your attention to the right side of the iPhone 5 smartphone.

• The motherboard is secured with five Phillips screws.
• At the top of the phone (the inner end of the case) there are two more bolts that secure the part we are dismantling.

Attention: before unscrewing the mentioned bolts, carefully disconnect all visible connecting components of the phone. Then carefully turn the board over to the left.

• Disconnect two coaxial cable(top and bottom area of ​​the board).
• Remove the motherboard of the smartphone from the depths of the case.

Now install new part in reverse order.

Summing up

As you may have noticed, replacing the iPhone 5 motherboard is quite easy. Even a person ignorant of electronics will be able to implement this kind of repair process without much difficulty. However, remember: extreme attention and caution in actions will significantly increase your chances of success of the enterprise. All the best!

Most expensive component Apple smartphones- this is the system board. For iPhone 5 and iPhone 5S, the new board will cost from 13 to 24 thousand rubles. You can save money if you purchase a component that has already been used - taken out of a phone that was sent for disassembly.

How much does a new motherboard cost?

The cost of a new motherboard for iPhone smartphones 5 and 5S depends on several factors. First of all, of course, the price depends on the generation of the device and the amount of installed permanent memory. In the case of 5 and 5S, prices are approximately as follows:

• The motherboard for iPhone 5 with 16 gigabytes starts from 13 thousand and ends 18 thousand rubles.
• For the fifth iPhone with 32 gigabytes of ROM - from 16 to 20 thousand.
• For a more modern model - 5S, but with a minimum amount of ROM, the motherboard costs 20-22 thousand rubles.
• 5S with 32 gigabytes – 20-24 thousand.

It should be noted that the prices indicated in the list are applicable for motherboards of phones that are certified in the Russian Federation. Some companies order components from abroad, and they do not always have the required certificate. They are usually cheaper, but problems can arise with them. For example, after replacing the board, the device may stop working with SIM cards Russian operators. An unlocking will be required, and this will cost additional money.

The second thing the cost depends on is greed of component suppliers and sellers. Some may set an inflated price tag for products, especially if they do not have serious competitors.

Cost of a used motherboard for iPhone 5 and iPhone 5S

Of course, the price of a new component for fifth-generation iPhones is quite high. However, fortunately, you can still save on repairs. So, for example, there is an option to install a motherboard that was previously in another smartphone.

For iPhone 5, the price of boards on electronic bulletin boards starts at 8 thousand rubles. This is much less than the cost of a new component. On the iPhone 5S, even for the version with 32 gigabytes of memory, you can purchase a motherboard for 10-12 thousand.

In large cities such as Moscow and St. Petersburg you can find even better offers. Up to 5-6 thousand rubles. Why so cheap? It's simple! For example, a person broke the screen and does not want to bother with repairs. Due to the fact that the device does not look quite appropriate, it is sold for almost nothing.

Why is the motherboard so expensive?

A motherboard for an iPhone is not a motherboard for a computer. Here are all the components (processor, RAM, permanent memory, various modules and sensors) are soldered. They are not officially shipped separately.

System board repair

If you want to save money, then instead of replacing the system board, you can use services for its repair. In 70-80% of cases, a malfunction in the device can be eliminated without replacing the entire board.

The cost of repairs varies depending on the type of repairs needed, as well as the firm's business strategy. However, on average, troubleshooting a system board costs from 1 to 5 thousand rubles. This is much less than the cost of a motherboard for an iPhone or iPhone 5S, even one that was removed from an old phone. Therefore, before buying a new board, it is strongly recommended to consult and find out: it may be possible to restore the functionality of your smartphone by replacing one component.

Bring your iPhone 5 back to life by replacing your failed motherboard.

Step 1 - Front Panel
* First, when disassembling your smartphone, make sure it is turned off.
* Unscrew the screws highlighted in the photo.

Step 2
*Attach the suction cup to the screen directly above Home button.
* The suction cup should stick well to the front panel.

Step 3
* While holding the iPhone with your right hand, pull the suction cup with your left to separate the front panel module from the phone body.
*You will need some time as the front panel module fits quite tightly to the body. But gradually remove the panel.
* Use a special spatula and insert it into the gap between the front and rear panels, separating them from each other. Continue to remove the front panel using the suction cup.

*Display module is coupled with rear panel several clamps. Therefore, you need to use both a suction cup and a spatula.

Step 4
* Use the plastic spatula left and right, moving around the perimeter of the iPhone and pushing away the clamps located there.

Step 5
* With all the clips free, remove the bottom of the front panel from the chassis.

* You will not be able to completely remove the front panel yet; it is still attached to the back panel with three cables.
* Position the front panel at a 90 degree angle to the rear panel.

Step 6
* Remove the three screws marked in the illustration that secure the front panel cable holder to the board.

Step 7
*The next step is to remove the cable holder.

Step 8
* Disconnect the three front panel module cables marked in the illustrations.

Step 9
* Separate the body and front panel.

Step 10 - Battery
*Remove the screws marked in the photo that secure the battery connector holder.

Step 12
* Use a special plastic spatula and remove the battery connector.
* Make sure that the spudger is lifting the battery connector and not the socket, otherwise the connector may be damaged.

Step 13
* Take a special plastic spatula and insert it between the battery and the case.

*Start on the right side of the battery. Peel it off using a plastic spatula.
* Be careful when lifting the battery. Don't damage it.

Step 14
* You can also use a special plastic tab and use it to peel the battery off the case.
*Remove the battery.

Step 15 – Motherboard
* Using a pointed tool, remove the antenna module cable connector (above the polyphonic module) from the motherboard.

Step 16
* Remove the screws shown in the picture that secure the motherboard holder located on the top of the motherboard.

Step 17
*Now take out the holder.

Step 18
* Use a flathead screwdriver to remove the cables shown in the photo from the sockets on the motherboard.

Step 19
* There are two screws at the top of the case - remove them.

Step 20
* Remove the screw that still holds the holder to the motherboard.

Step 21
* Now you can remove the unsecured holder.

Step 22
*If you have a special SIM eject tool, use it to release the tray or use a paper clip.

* Remove the SIM card tray from the smartphone.

Step 23
*Remove the screws shown in the photos. They hold the motherboard.

Step 24
* Turn the motherboard towards the direction where the battery was located.
* Do not remove the board completely yet, it is connected to the smartphone by a cable Wi-Fi antennas, located on the back of the motherboard.

Step 25
*Now disconnect this cable by lifting the connector with a pointed tool.

Step 26
* Remove the motherboard.
* While the board is separated from the smartphone, place it on an anti-static grounding mat.

Step 27 – Rear Camera
* Remove the two screws securing the holder rear camera on the motherboard.

Step 28
*Remove the rear camera holder from the motherboard.

Step 29
*Use a flathead screwdriver to remove the rear camera cable from the connector on the motherboard.

Step 30
* Remove the rear camera.

Step 31 – Motherboard
*Use a flathead screwdriver to remove the cable connectors from the sockets on the motherboard.

Step 32
* Remove both connecting cables from the board.

Step 33
*You will still have the motherboard.

To reassemble your smartphone, follow the instructions in reverse order.